Mechanical properties of clay‐reinforced polyamide

Intercalated and exfoliated nanocomposites were prepared by extrusion and injection of polyamide‐6 and highly swollen or slightly swollen montmorillonite, respectively. The microstructure of the nanocomposites has been studied previously. In this article, we investigated the influence of the preferential orientation of the montmorillonite sheets on the mechanical properties of the nanocomposites. Dynamic mechanical analysis and tensile tests showed that the elastic modulus depends mainly on the filler loading. A parallel coupling could well account for the behavior of the nanocomposites. The calculated elastic and storage moduli of montmorillonite were set to 140 and 40 GPa, respectively. Compression tests were performed to study the anisotropy of the mechanical properties. The elastic modulus and flow strain were sensitive to the filler orientation. A Tandon–Weng approach was applied to consider the geometry of the filler. In all low‐deformation tests, no significant difference between intercalated and exfoliated systems was observed. Finally, the influence of the dispersion and exfoliation state of the filler on the ultimate properties of the nanocomposites (tensile tests) is discussed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 272–283, 2002     

Crosslinked polystyrene with improved mechanical properties

The synthesis of some divinyl monomers—bis(vinylphenyl)ethane ( 2 ), bis(vinylbenzyloxy)hexane ( 3a ), and bis(vinylbenzyloxy)dodecane ( 3b ) is reported. Copolymers of the new monomers and styrene were evaluated as an alternative to divinylbenzene-crosslinked polymers for use as matrices and absorbents. The mechanical properties and the amount of residual double bonds in the copolymers were compared. It was found that the new copolymers, unlike the divinylbenzene-crosslinked polymers, retained their mechanical strength even at high crosslinking degrees. Stress at break values of 79, 68, and 18 N/mm² were found for the polymers crosslinked with 20 mol % of 3a, 2 , and divinylbenzene; 5, 25 and 45% of the divinyl units in these polymers were left as pendant double bonds. Porous styrene– 2 copolymers were synthesized and shown to have lower surface areas than the corresponding divinylbenzene-crosslinked polymers. The pore size distribution showed that this was due to the absence of the smallest pores which are found in the divinylbenzene-crosslinked polymers in between heavily crosslinked nodules. © 1993 John Wiley & Sons, Inc.     

Laser field induced charge transfer: Para-nitroaniline coupled to a quantum mechanical radiation field

Summary We present a preliminary model for describing a solvated intramolecular charge transfer reaction coupled to a quantum mechanical radiation field. Actual calculations of energies and couplings were performed with a recently developed self-consistent reaction field response method. The representation of dressed molecular states is used for calculating state populations for various laser fields. The state populations are sensitive to the properties of the laser field.     

Mechanical properties of single motor molecules studied by three-dimensional thermal force probing in optical tweezers.

A new method combining three-dimensional (3D) force measurements in an optical trap with the analysis of thermally induced (Brownian) position fluctuations of a trapped probe was used to investigate the mechanical properties of a single molecule, the molecular motor kinesin. One kinesin molecule attached to the probe was bound in a rigorlike state to one microtubule. The optical trap was kept weak to measure the thermal forces acting on the probe, which were mainly counterbalanced by the kinesin tether. The stiffness of kinesin during stretching and compression with respect to its backbone axis were measured. Our results indicate that a section of kinesin close to the motor domain is the dominating element in the flexibility of the motor structure. The experiments demonstrate the power of 3D thermal fluctuation analysis to characterize mechanical properties of individual motor proteins and indicate its usefulness to study single molecule in general     

The effect of grass fiber filler on curing characteristics and mechanical properties of natural rubber

Natural rubber is reinforced with a novel type of grass fiber (Cyperus Tegetum Rox b). The effects of fiber loading of different mesh sizes on curing characteristics and mechanical properties of grass fiber filled natural rubber composite are studied. Since 400 mesh grass fiber loaded natural rubber composite shows superior mechanical properties, therefore the effect of silane coupling agent was studied for this particular composite. Here composites were prepared by using water leached grass fiber. Optimum cure time increases with the increase in fiber loading but the change in scorch time is less. The same trend of increase in optimum cure time is observed in the presence of Si69. But the value is higher compared to that of rubber composite without Si69. With increase in the fiber loading, modulus and hardness of the composite increases but tensile strength decreases. The mechanical properties of the composite, namely moduli at 200 and 300% elongation and hardness increase in the presence of Si69 but tensile strength is less compared to that of the composite without Si69. Elongation at break is not much affected due to the presence of Si69. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and properties of composites made from rice straw and poly(vinyl chloride) (PVC)

Rice straw was employed for the preparation of lignocellulosic‐poly(vinyl chloride) (PVC) composites. The effect of pretreatment of rice straw, concentration of PVC, pressure as well as pressing temperature on the mechanical properties and water absorption was studied. Also, the effect of lignin as coupling agent on the mechanical properties and water absorption of composite was studied. Composites of rice straw comprising both PVC and a coupling agent offer superior properties compared to those made from only rice straw and PVC. The extent of improvement in the mechanical properties and dimensional stability of composites depended not only on the pretreatment of rice straw, concentration of PVC and lignin but also on pressure and pressing temperature. Copyright © 2004 John Wiley & Sons, Ltd.     

PREPARATION AND ELECTROCHEMICAL CHARACTERISTICS OF POLYMER ELECTROLYTE MEMBRANES BASED ON SAN/PVDF-HFP BLENDS

A copolymer of poly(acrylonitrile-co-styrene) (SAN) was synthesized via an emulsion polymerization method. Novel polymer electrolyte membranes cast from the blends of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), SAN and fumed silica (SiO2) are microporous and can be used in polymer lithium-ion batteries. The membrane shows excellent characteristics such as high ionic conductivity and good mechanical strength when the mass ratio between SAN and PVDF-HFP and SiO2 is 3.5/31.5/5. The ionic conductivity of the membrane soaked in a liquid electrolyte of 1 mol/L LiPF6/EC/DMC/DEC is 4.9×10-3 S cm-1 at 25℃. The membrane is electrochemical stable up to 5.5 V versus Li /Li in the liquid electrolyte. The influences of SiO2 content on the porosity and mechanical strength of the membranes were studied. Polymer lithium-ion batteries based on the membranes were assembled and their performances were also studied.     

The IINS, IR and DFT studies of hydrogen bonds in 6-Furfuryl and 6-Benzylaminopurines

FTIR and IINS spectra of 6-Furfurylaminopurine (6-FAP) and 6-Benzylaminopurine (6-BAP) taken at different temperatures have been analysed and compared with the spectra calculated by the ab initio DFT/B3LYP method and the semiempirical PM3 method in the isolated molecule approximation, for the tautomers N3-H, N7-H and N9-H, and dimers with hydrogen bonds. For 6-FAP the best agreement between the calculated and experimental (at 20 K) spectra has been found for the N9-H tautomer, whose structure was established by X-ray diffraction. For 6-BAP the analogous agreement for the N9-H tautomer structure has been poor and much better for the N7-H tautomer. The vibrational spectra calculated for dimers of the molecules studied involved in hydrogen bonds, permitted also an interpretation of the bands whose positions and FWHM in the FTIR spectra changed with temperature.     

聚丙烯微孔膜基渐变聚合物的制备,结构与性能的研究

以聚丙烯微孔膜为基材，通过扩散控制原位共聚合的方法在人填充了组成沿膜的厚度方向逐渐改变的无规共聚物，Ｘ－光电子能谱（ＸＰＳ）、全反射红外光谱（ＡＴＲ）以及动态粘弹谱的分析结果。说明所制备得到的合膜具有明显的渐变聚合物性质。     

The chemistry of fluorine containing phosphaalkenes, arsaalkenes and selenocarbonyls

This review covers our extensive research activities in the area of fluorine containing phospha- and arsaalkenes as well as selenocarbonyls, which differ considerably in their properties and reactivities from their alkyl and aryl counterparts and thus contribute in a gratifying manner to the still growing field of unsaturated element-carbon compounds of 3rd and 4th row main group elements E. Of particular interest is the influence of the fluorine substituents and other small groups (OR, NR₂) with either inductive and/or mesomeric effects on the polarity and reactivity of the EC bond. Addition reactions of proton acidic and hydridic polar HX reactants as well as [2+2], [3+2] and [4+2] cycloadditions have been thoroughly studied. The results obtained allow a classification of the EC systems within five different types, A to E, and prove a change from “normal” to “inverse” heteroalkenes in this sequence. The ligand properties of some derivatives have also been investigated in some detail.